Adress:Weihai Road, Jing'an District, Shanghai

welded sonic testing tube steels

Contact us

Standard Practice for Ultrasonic Testing of the Weld Zone

1.1 This practice 2 describes general ultrasonic testing procedures for the detection of discontinuities in the weld and adjacent heat affected zones of welded pipe and tubing by scanning with relative motion between the search unit and pipe or tube. When contact or

Reply

Non Destructive Test (NDT) for Welded Tube

Since each testing technology has inherent capabilities and limitations, the optimum test solution for welded tube could be a combined system that utilizes both Eddy Current and Ultrasonic test instruments or other combinations to fit the needed task.

Reply

Easy-to-install sonic tube system for CSL - Dextra Group

Easy-to-install sonic tube system for CSL Sonitec is a tube solution invented to facilitate the integrity testing of foundations using the CSL testing method. CSL (Cross Sonic Logging) method allows to determine the structural integrity and homogeneity of concrete within diaphragm walls, bored piles, drilled shafts, barrettes, concrete piles or

Reply

Standard Specification for Steel Tubes, Low-Carbon or High

A595 / A595M-18 Standard Specification for Steel Tubes, Low-Carbon or High-Strength Low-Alloy, Tapered for Structural Use low-carbon steel~ steel tubes~ seam-welded steel tubes~ A370 Test Methods and Definitions for Mechanical Testing of Steel Products.

Reply

Welded Pipe Manufacturers American Piping Products

We have welded pipe for every need. Some manufacturers are TMK Ipsco, Northwest Pipe, Tenaris, American Steel Pipe, and Southland Tube. By continuing to browse this website, you agree to the use of cookies for statistical purposes as well as third party cookies generated by

Reply

Ultrasonic Testing of Metal Bars and Tubular Products

Oct 12, 2015 · Seam welded tubes and pipes are commonly tested for cracking or lack of penetration with transducers aimed circumferentially. Bar testing typically employ multiple inspection channels operating in parallel, with one beam aimed straight at the center of the bar to identify laminar cracks and piping,

Reply

Ultrasonic Testing of Structural Welds

Ultrasonic Testing of Structural Welds DEXTER A. OLSSON, Bethlehem Steel Corporation During the past five years Bethlehem Steel Corporation has de­ veloped and applied techniques for the ultrasonic testing of butt welds which provides an assurance of weld quality similar to that achieved with radiography. Although there are no revolu­

Reply

A GUIDE FOR ULTRASONIC TESTING AND EVALUATION

place~”on top of the weld and moved along its length, Fig. A-g. b. For welds not ground smooth the transducer is placed alongside and not quite parallel to the weld and moved along the length, Fig. A-10. The entire weld and heat affected zone should be scanned. The weld should be inspected from both sides of one surface.

Reply

Ultrasonic Testing FAQ Olympus IMS

Ultrasonic nondestructive testing, also known as ultrasonic NDT or simply UT, is a method of characterizing the thickness or internal structure of a test piece through the use of high frequency sound waves. The frequencies, or pitch, used for ultrasonic testing are many times higher than the limit of human hearing,

Reply

STEEL TUBE AND PIPE HANDBOOK

5 Precision cold drawn seamless steel tubes Page 60 Standard precision tubes Page 60 Cylinder tubes (for mechanical treatment – HPZ) Page 72 Cylinder tubes (HP – „ready to use“) Page 74 Tubes for hydraulic and pneumatic lines – HPL Page 76 Tubes for automotive industry Page 84 Injections tubes (for Diesel engines) Page 84 Bearings tubes Page 85 Precision welded steel tubes Page 86

Reply

Using NDT systems to monitor welded tube production

Nov 15, 2001 · Ultrasonic testing normally is used to find long, continuous defects, such as incomplete seam welds. It is possible to use ultrasonic testing to find small defects; however, this requires transducers with limited beam coverage. Effective use of this type of transducer requires reducing the tube mill throughput to unacceptably slow speeds.

Reply

Welds testing - OKOndt

Thus, we have considered the main methods of non-destructive testing of welds. It is obvious that the combined use of ultrasonic, eddy current and magnetic particle inspections ensures the most accurate test results and the safe test conditions.

Reply

Using NDT systems to monitor welded tube production

Nov 15, 2001 · Ultrasonic testing normally is used to find long, continuous defects, such as incomplete seam welds. It is possible to use ultrasonic testing to find small defects; however, this requires transducers with limited beam coverage. Effective use of this type of transducer requires reducing the tube mill throughput to unacceptably slow speeds.

Reply

Non Destructive Testing of Steels – IspatGuru

Jan 19, 2015 · Dye penetrant test, eddy current testing, magnetic particle test, Non destructive testing, radiography test, ultrasonic testing, Non Destructive Testing of Steels Non destructive testing (NDT) of steels is a group of analysis techniques used for evaluating the properties of steel materials, components, or welds without causing any damage to them.

Reply

Physical Weld TestingDestructive & Nondestructive - Weld

Dec 12, 2019 · The back bend test is a type of physical weld testing that is used to determine the quality of the weld metal and the degree of penetration into the root of the Y of the welded butt joint. The specimens used are similar to those required for the free bend test except they are bent with the root of the weld on the tension side, or outside.

Reply

Standard Specification for Steel Tubes, Low-Carbon or

The tube steel shall be hot-rolled aluminum-semikilled or fine-grained killed sheet or plate manufactured by one or more of the following processesopen-hearth, basic-oxygen, or electric-furnace. The tubes shall be made from trapezoidal sheet or plate that is preformed and then seam welded.

Reply

Pipe Inspection, Testing & Marking

Product Analysis – Chemical & Mechanical Testing of Pipe During manufacturing, different types of pipe inspection and testing are done to ensure the quality of the pipes. Metallurgical Tests Metallurgical Tests confirm that the chemical requirements of pipe are as per the material standard. Metallurgical Tests are normally known as Micro and Macro pipe inspection & testing. Micro Analysis or

Reply

Stainless Steel Feedwater Heater Tube - Dongshang Stainless

Welded and Cold Drawn Stainless Steel Tube. With improvement of technology in welded tube manufacturing, more and more project require welded tubes for feedwater heater system, compared to seamless tube, welded tube have several advantages, like cost effective, short delivery time, tight tolerances and so on.

Reply

CSL (Cross Sonic Logging) Tubes – Pittsburgh Pipe

CSL Tubes are to be threaded with watertight caps and couplers and meet the specifications of ASTM – A53 Grade B U.S. Steel with mill test reports. Uniquely Designed Pittsburgh Pipe has become the premier CSL testing tube manufacturer in the United States.

Reply

Contact us